This article is a mirror article of machine translation, please click here to jump to the original article.

Architect_Programmer_Code Agriculture Network»Architect › Other Technologies › Network technology › Cisco routing command summary
View: 13142|Reply: 2

[Router] Cisco routing command summary

[Copy link]
Posted on 2/5/2015 12:41:28 PM | | |
Router command base - mode conversion command
User mode ---- privileged mode, using the command "enable"
Privileged mode ---- global configuration mode, using the command "config t"
Global configuration mode ---- interface mode, use the command "interface+interface type+interface number"
Global configuration mode ---- wire control mode, use the command "line+interface type+interface number"
Notes:
User mode: View initialization information.
Privileged mode: View all information, debug, and save configuration information
Global mode: Configure all information for all interfaces for the entire router or switch
Interface mode: The configuration for a certain interface
Wire control mode: the interface configuration for controlling the router
Router command basics - configuration commands
show running config to show all configurations
show versin displays the version number and register value
shut down the interface
no shutdown to open the interface
ip add +ip address Configure the IP address
secondary+IP address Configure a second IP address for the interface
show interface+interface type+interface number View interface manageability
show controllers interface to see if the interface has a DCE cable
show history to view history
show terminal to see the terminal record size
hostname+hostname Configure the identity of the router or switch
config memory modifies the boot configuration saved in NVRAM
exec timeout 0 0 sets the console session timeout to 0
service password-encryptin Manually encrypt all passwords
enable password + password Configure the plaintext password
ena sec + cipher configuring ciphertext passwords
Line VTY 0 4/15 enters the telnet interface
password + password Configure the telnet password
line aux 0 enters the AUX interface
password + password Configure the password
line con 0 enters the CON interface
password + password Configure the password
bandwidth+number to configure the bandwidth
no ip address to delete the configured IP address
show startup config to view the configuration information in NVRAM
copy run-config atartup config to save information to NVRAM
write to save the information to NVRAM
erase startup-config to clear the configuration information in NVRAM
show ip interface brief View the interface demotion information
banner motd # + info + # configure the pixel information of the router or switch
description+info Configure the interface to listen to the tracing information
VLAN database enters VLAN database mode
VLAN + VLAN Number + Name Create a VLAN
switchport access vlan + vlan number is the VLAN as the interface interface
interface vlan + vlan number to enter VLAN interface mode
ip add +ip address Configure the management IP address for the VLAN
vtp+service/tracsparent/client to configure the VTP operation mode of SW
vtp + domain + domain name Configure the VTP domain name of SW
vtp + password + password Configure the password for SW
switchport mode trunk to enable relay
no vlan +vlan number Delete the VLAN
show spamming-tree vlan +vlan number Check the VLA fear of spamming tree discussions
Router command basics - configuration commands
IP route + non-direct CIDR block + subnet mask + next-hop address Configure the static/default route
show ip route to view the routing table
show protocols shows all passive routing protocols and which protocols are set on the interface
show ip protocols shows the route selection protocol configured on the router, and gives information such as the timer used in the route selection protocol
router rip activates the RIP protocol
network + direct network segment Publishes the direct connection network segment
interface lookback 0 activates the logical interface
passive-interface + interface type + interface number Configure the interface to passive mode
debug IP + protocol dynamically view route update information
undebug all disables all DEBUG information
router eigrp +as number activates the EIGRP routing protocol
network + CIDR block + subnet mask Publish a direct connection to the CIDR block
show ip eigrp neighbors View the neighbor table
show ip eigrp topology to view the topology table
show ip eigrp traffic to see the number of packets sent
router ospf +process-ID to activate the OSPF protocol
network+direct network segment+area+area code Publishes the direct connection network block
show ip ospf displays the process number and ROUTER-ID of OSPF
encapsulation+package format Change the package format
no ip admain-lookup turns off the router's domain name lookup
IP Routing enables routing on Layer 3 switches
show user to see the online users of SW
clear line + line number Clear line




Previous:C# is commonly used regular expressions
Next:Build a mail server with Winmail

Related Posts
Posted on 12/2/2015 3:41:01 PM |
Is this the administrator of the Wusoft Forum?
 Landlord| Posted on 12/2/2015 3:43:28 PM |
Manshow posted on 2015-12-2 15:41
Is this the administrator of the Wusoft Forum?

Hello
Disclaimer:
All software, programming materials or articles published by Code Farmer Network are only for learning and research purposes; The above content shall not be used for commercial or illegal purposes, otherwise, users shall bear all consequences. The information on this site comes from the Internet, and copyright disputes have nothing to do with this site. You must completely delete the above content from your computer within 24 hours of downloading. If you like the program, please support genuine software, purchase registration, and get better genuine services. If there is any infringement, please contact us by email.
Mail To:help@itsvse.com